IE4 represents the super premium efficiency class in IEC 60034-30-1 and sits one step beyond IE3. For facilities where energy cost weighs heavily on the budget, IE4 pushes losses lower still and grows the annual saving. As a manufacturer-supplier that builds the IE4 series on its own production line and delivers from stock, HEM Motor offers this class with both technical and commercial advantages.
Our IE4 range spans 0.25 kW to 355 kW, with a Ø100 mm shaft diameter on the largest frame. The motors are built with IP55 protection and Class F insulation, and slip near full load is about 4%. Paired with a frequency inverter, system efficiency rises further, yielding extra savings in variable-load applications.
Although the initial cost is slightly above IE3, in continuous applications the gap is closed by savings. For top efficiency see our IE5 series, and for harsh environments our cast iron body models. For the right IE4 selection and a quote, call +90 (532) 345 49 86 or use our contact page.
In small-power induction motors, efficiency is the parameter most often overlooked yet most impactful over the long run. Motors that fit IEC 80 and 90 frames, such as 0.75 and 1.1 ... More Details
22 kW and 45 kW are among the most in-demand power ratings in industry. The vast majority of pump, fan, compressor, conveyor and general drive applications fall exactly into this p... More Details
When buying an IE4 super premium efficiency class motor, most users focus only on the efficiency percentage and the power; yet one of the most critical acceptance criteria determin... More Details
IE4 super premium efficient motors today mostly run together with a variable frequency drive (VFD/inverter), because turning efficiency into real savings is only possible by runnin... More Details
There is more than one way to reach the IE4 (super premium) efficiency class defined by IEC 60034-30-1. One of them is the Line-Start permanent magnet motor, which can run directl... More Details
IE4-class 15 kW and 18.5 kW motors are among the most sought-after power ranges in industrial facilities in Turkey. In pump, fan, compressor, conveyor and general process drives, t... More Details
Among IE4 super premium motors, 7.5 kW and 11 kW are by far the two most sought-after power ratings in pump, fan and compressor applications. The popularity of these two powers is ... More Details
Expressions such as "insulation class F" and "temperature rise class B" on an electric motor's nameplate are, for most users, treated as the same thing or confused with one another... More Details
When connecting an IE4 motor to your panel, attention usually goes to cable cross-section and correct terminal bridging; yet how tightly the terminal bolts are torqued is just as c... More Details
A standard electric motor has a single shaft end, and all torque is transmitted from that end. In some applications, however, an output is also needed at the rear of the motor: a s... More Details
When ordering an IE4 Super Premium motor, choosing the right kW, speed and efficiency class alone is not enough. The mounting range that determines how the motor connects to the ma... More Details
When selecting an IE4 motor, most engineers and buyers first evaluate the power rating, speed, mounting type (B3, B5, B14) and efficiency class. These are, of course, the right sta... More Details
The IE4 efficiency class represents one of the highest practical efficiency levels industry can reach with electric motors, and it sits on the agenda of every facility that wants t... More Details
When ordering an IE4 super-premium efficient electric motor or replacing an existing motor, reading the nameplate (label) in full is the strongest barrier against an incorrect deli... More Details
When an IE4 super premium motor fails, the first question is usually the same: "Should I rewind it or buy a new one?" On a standard motor, rewinding is often a reasonable option; b... More Details
However safely an IE4 motor runs at a sea-level plant, running that same motor at the same power at a mine or highland facility at 1500 metres may not always be possible. The reaso... More Details
If you run your IE4 motor with a variable frequency drive (VFD) to produce continuous full torque at low speed, the fan on the motor's own shaft end may let you down halfway. In a ... More Details
In most industrial applications, 2-pole (3000 rpm) and 4-pole (1500 rpm) motors are standard; however, some jobs by their nature demand low speed. Large-diameter fans, slow mixers,... More Details
A screw air compressor is one of the longest-running pieces of equipment in most facilities; it often runs continuously at full load 16–24 hours a day. For this reason, selecting t... More Details
Plastic extruders and continuous process lines are among the most demanding applications for an electric motor: the motor turns 24 hours a day, often seven days a week, at a high a... More Details
English
Türkçe